Repair Corroded Battery Compartment

Can You Use Any Charger With Any Mobile Phone, Laptop, Camera, or Tablet? 

Every cell phone, laptop, and tablet seem to come with their own charger.  If you’re like me, you’ve probably compiled quite a few chargers through the years.  So the question becomes: is it safe to use a charger with your phone, laptop, camera, or tablet that isn’t the original manufacturer’s charger which came with the device?

Types of Chargers

In this guide, we’ll focus on three types of chargers: laptop chargers, micro USB chargers (these are used with telephones, tablets, and cameras), and Apple Lightning Connectors.  While some devices have chargers using a slightly different head or charging cable, these are the most common.

Laptop chargers are fairly unique to the device they include.  However, there can be some generic chargers which boast the capability to be interchanged between notebooks.  This always requires changing of this charger”head” and may not be the best charging amperage or voltage to your device.

Micro USBs are designed to be interchangeable, and are standard in most smartphones, Android apparatus, and tablets.  Micro USB chargers typically have the exact same voltage, but may draw different amps.  I will explain this further later and how to know whether the charger is safe to use (depending on its recorded amps and voltage).

Apple Lightning Connectors are standard on all new Apple devices, such as iPads and iPods. For older devices with a 30-pin charge interface, a connector can be used to charge with the Lightning Connector.

For a charger to be used on a different device, it’s important that the plug  of the charger (the”head”) fit securely into the charging port of the device.  Micro USBs are the same across the board so far as charging heads, while laptop chargers are usually specific to both make and model.  However, the plug fitting firmly is only one part of this equation.

Somewhere on the power brick of the charger you will find a label with the charger’s voltage (V) and amperage (A).  For laptop chargers, this charging brick is often halfway down the charger and typically looks exactly like it sounds — a brick. For other types of chargers, like a smartphone charger, this information is usually located at the base of the charger, where it would meet the wall.  For the device you are attempting to control, the voltage and amperage required will be seen on the battery that came with the device or on the manufacturer’s website.

Voltage is how much power the charger will draw in the apparatus, or just how much is being”pushed” into the apparatus by the charger.  A phone will usually pull up to around 5V, though a notebook can pull up to 25V.  A charger must equal the voltage needed by the device.  This is important: drawing too high of a voltage could short out the device and potentially even begin a fire, while too low a voltage will fail to charge the battery.

Amperage is how quickly power is”pulled” into the apparatus, or how much electricity is used by the device.  The amount of volts will never change, but the amount of amps that the system pulls may change based on how hard the unit is working.  The number that you find on the battery that came with your device are the maximum amount of amps that may be pulled by the device.  In order to exchange chargers, the amp number on the charger must equal or exceed the amp number recorded on the device’s battery. If a device is paired with a charger that cannot support the amp requirement, it can burn out the power source and kill the apparatus.

So for those who have a modern USB device (smart phone, tabletcomputer, or camera) you can plug into a high-amperage USB port and enjoy quicker charging (so long as the voltage is equal).  *Site Note: if you have an older device, it may not work with USB interfaces that employ the new Battery Charging Specification.

If The Micro USB  Charger’s Voltage Is Not 5v…

Some devices might have their voltage recorded using a plus/minus on it like this: 5v +- 5%.  If this is the case, you may use a charger rated at 4.75 to 5.25v because that rating is telling you is that the device can take 5v minus 5 percent of 5v = 4.75 volts  OR  5v and 5 percent of 5v = 5.25 volts. 

An interesting thing to note is chargers supply a higher voltage than the batteries they charge.  That is pretty much how they work.  There has to be a voltage differential to produce the necessary current flow in the proper way to charge the battery.  If you look at your car, it’s a 12V battery, but typical alternators provide 13.8 to 14.4V charging voltage to the battery.

The problem with knockoffs, especially cheap knockoffs, is that they frequently don’t support the energy requirements of the apparatus, or aren’t built to maintain a steady flow safely.  This can cause damage to the device but can also pose a safety/fire hazard. Overall, it’s best to stick with the charger made for the device you are using.

Now You Understand How to Safely & Effectively Swap Chargers

I hope this article was able to assist you.  Now you know how to safely and effectively use a charger that did not come with your smart phone, notebook, camera, tabletcomputer, or other device.  Be sure you follow what we said and you should be ready to go!