Can You Use Any Charger With Any Cell Phone, Notebook, Camera, or Tablet?
Every cell phone, laptop, and tablet appear to come with their own charger. If you’re like me, you have probably compiled quite a few chargers over the years. So the question becomes: is it safe to use a charger with your phone, laptop, camera, or tablet that is not the original manufacturer’s charger that came with the device?
Kinds of Chargers
In this guide, we will concentrate on three types of chargers: notebook chargers, micro USB chargers (these are used with phones, tablet computers, and cameras), and Apple Lightning Connectors. While some devices have chargers using a slightly different head or charging cable, these are the most common.
Laptop chargers are fairly specific to the device they come with. However, there can be some generic chargers that boast the ability to be interchanged between laptops. This always requires changing of the charger”head” and may not be the best charging amperage or voltage for your device.
Micro USBs are theoretically designed to be interchangeable, and are standard in most smartphones, Android devices, and tablets. Micro USB chargers typically have the same voltage, but may draw different amps. I’ll explain this further later and how to know whether the charger is safe to use (based on its listed amps and voltage).
Apple Lightning Connectors are standard on all new Apple devices, including iPads and iPods. For older devices using a 30-pin charge interface, a connector can be used to control the Lightning Connector.
In order for a charger for use on another device, it’s important that the plug of the charger (the”head”) fit snugly to the charging port of the unit. Micro USBs are the same across the board as far as charging heads, whilst laptop chargers are usually specific to both make and model. However, the plug fitting securely is only one part of the equation.
Determined by the power brick of the charger you’ll find a label with the charger’s voltage (V) and amperage (A). For other types of chargers, like a smartphone charger, this information is usually found at the base of the charger, in which it would meet the wall. For the device you’re attempting to control, the voltage and amperage required will be seen on the battery that came with the device or on the manufacturer’s website.
Voltage is how much power the charger will draw in the apparatus, or just how much is being”pushed” to the device by the charger. A phone will usually pull up to approximately 5V, though a laptop can pull up to 25V. A charger must equal the voltage required by the device. This is important: drawing too high of a voltage could short out the device and potentially even begin a fire, while too low a voltage will fail to charge the battery.
Amperage is how quickly power is”pulled” into the apparatus, or how much power is used by the device. The quantity of volts will never change, but the quantity of amps that the system pulls may change depending on how hard the unit is working. The number that you locate on the battery that came with your device will be the max amount of amps that can be pulled from the device. To be able to swap chargers, the amp number on the charger must equal or exceed the amp number listed on the device’s battery. If a unit is paired with a charger that cannot support the amp requirement, it can burn out the power supply and kill the apparatus.
So for those who have a modern USB device (smart phone, tabletcomputer, or camera) you can plug into a high-amperage USB port and enjoy quicker charging (so long as the voltage is equal). *Site Note: if you have an older device, it may not work with USB ports that employ the new Battery Charging Specification.
If The Micro USB Charger’s Voltage Isn’t 5v…
Some devices might have their voltage listed using a plus/minus on it like this: 5v +- 5%. If this is true, you may use a charger rated at 4.75 to 5.25v because that rating is telling you is that the device can take 5v minus 5% of 5v = 4.75 volts OR 5v plus 5% of 5v = 5.25 volts. So this means anything between 4.75 t0 5.25v is safe to use (so long as the amperage of the charger is equal to or higher than the device’s listed amperage).
An interesting thing to note is all chargers supply a higher voltage than the batteries that they charge. That is pretty much how they operate. There needs to be a voltage differential to generate the necessary current flow in the proper way to charge the battery. If you look at your vehicle, it’s a 12V battery, but typical alternators provide 13.8 to 14.4V charging voltage to the battery.
The problem with knockoffs, especially cheap knockoffs, is that they often don’t support the energy requirements of the apparatus, or are not built to maintain a steady flow safely. Overall, it’s best to stick with the charger made for the device you are using.
Now You Know How To Safely & Effectively Swap Chargers
I hope this article was able to assist you. Now you know how to safely and efficiently use a charger that did not come with your smart phone, notebook, camera, tablet, or other device. Make certain you follow what we said and you should be good to go!